Are you having trouble in the installation and repair of water pipelines at your home? How do you attach Shark Bites to copper pipes? Will SharkBite fittings work on copper pipe? How do you install a SharkBite angle stop on a copper pipe?HOW TO INSTALL SHARKBITE VALVE ON COPPER These are some common questions that might pop up in your mind when you think about installing or repairing water pipelines across your house all by yourself. Though it may otherwise be a time taking and messy job, it is quite easy with the SharkBite fittings.

HOW TO INSTALL SHARKBITE VALVE ON COPPER
HOW TO INSTALL SHARKBITE VALVE ON COPPER

If these are among a few questions in your mind, this article is for you to read. Clarify all your doubts related to the SharkBite valve on copper in this article. The article takes you through the little details of the installation and the disconnection of SharkBite fittings.

How Do You Install A SharkBite Angle Stop On A Copper Pipe?

The installation and repair work of pipelines within your home generally requires you to be using crimpers, adhesives, or solder. However, all of these tools and aids to repair and install your water lines have several drawbacks and require you to have patience and expertise. SharkBite fittings on the other hand give you an easy and hassle-free installation of water pipes which you can do all by yourself.

There are just two essential steps involved in the process of installing SharkBite fittings on copper pipes, first is to cut the pipe to the size and the second is to push and fix it to the appropriately sized SharkBite fitting.

It is just as easy as it sounds and this article will take you through the minor details of the process and the product for a much clearer understanding.The most crucial and tough part in the installation of the valve on copper is the measurement of the pipe to find the correct size of the fitting to be used. This step is most crucial as it prevents damages and helps in the correct installation of the pipe. Several tutorials will help you through this.

You can also refer to the charts to get an idea of the measurements and their suitable fittings. This will help you get a better idea of the sizing since keeping in mind, both, the inner, as well as the outer diameter, can be challenging. After measuring the diameter you also have to convert it to a nominal diameter depending on whether you are using a female or a male thread.

HOW DO SHARKBITE FITTINGS WORK?

These simple plumbing fittings are designed as a push-to-connect system and create very strong connections and support an easy and simple installation. There are two stages to the working of the push-to-connect system of SharkBite. The first stage involves the insertion of the pipe into the fitting and passing through a release collar. It then grabs a ring made of stainless steel. The teen on the grab ring then opens out and grips onto the pipe.

In the second stage, the pipe gets pushed into an o-ring protector that then aligns the pipe. The o-ring is formulated specially to be able to compress in the middle of the pipe and the wall of the fitting.

This happens before the end of the pipe reaching the tube stop. Once the pipe passes through the o-ring and hits the top of the tube, a secure joint along with a watertight seal is created.

The manufacturers of the SharkBite fittings, Reliance Worldwide recommend these fittings to be used for tubing or piping certified terms that include Copper (ASTM B 88), PEX (ASTM F876, CSA B137.5), and CPVC (ASTM D 2846, CSA B137.6).

HOW TO INSTALL A SHARKBITE VALVE ON COPPER?

Before the installation of the SharkBite, you have to secure the correct size fitting and the piping. Once that is secured you must check if the fitting and piping are in good condition, clean, dry, and do not contain any foreign particles. Once you’ve checked for apparent damages and the sizing you must follow the given steps for the installation of the valve.


1). CUT THE COPPER PIPE:
Cut the pipe such that the ends are square and flush, using a rotary tube cutter. There should not be any damages on the cut ends.
2). USE SHARKBITE DEPTH DEBURR GAGE FOR THE MARKING OF THE INSERT DEPTH:
The SharkBite Depth Deburr is a product sold independent of the fitting but must be used to mark the insert depth on the outside of the pip alongside a permanent marker. This mark plays an important role in the correct and accurate installation of the valve on copper.
3). INSERTION OF THE PIPE IN THE SHARKBITE FITTING:
The insertion of the pipe has to be done through the release collar permitting it to sit against the grab ring.
4). PUSH THE PIPE: 
Once inserted, you should push the pipe using slight twisting motions firmly into the SharkBite fitting until you hit the tube stop.
5). ENSURE PROPER PLACEMENT: To check if the installation of the pipe is accurate and proper, you must verify and see if the depth marked is within 0.005 inches of the release collar ending.

HOW LONG DO SHARKBITE FITTINGS LAST ON COPPER? 


Correctly installed SharkBite fittings can be long-lasting. When used along with the SharkBite tubing, fittings by SharkBite are covered under a warranty period of 25 years. As long as, the installation of the SharkBite fitting is done properly, the fittings can last up to anywhere around 30 to 35 years.

HOW TO INSTALL SHARKBITE VALVE ON COPPER

CAN I USE SHARKBITE FITTINGS UNDERGROUND? 

The general recommendations suggest the fittings be used under an access panel. However, SharkBite panels have been tested and certified by IAPMO and are approved for underground use as well as usage behind the wall.

Using push-to-connect fittings is a better option for underground installations as they make the work easier and more convenient. Using silicone tape to wrap the fittings is a good idea for underground fittings since the soil contains chemicals that can otherwise cause damage and breakage in the fittings. The tape will also add an extra layer of security to the connection of the fittings and the pipe.

THE DISCONNECTION OF A SHARKBITE FITTING:

The disconnection of the fittings is just as simple as the installation. For the disconnection of a SharkBite fitting, you need to use a disconnect clip or disconnect tongs. Using either one of these tools, all you have to do is to apply pressure which will help release the collar. This will play the grab teeth effectively and will result in the release of the pipe allowing the pipe to be disconnected to the fitting.

The SharkBite disconnect clips must be used such that the logo faces the opposite of the release collar. It is important to note that you must push the clip against the release collar and the tube must be pulled out in a twisting motion to release. If you use the SharkBite disconnect Tongs, you must make sure that the teeth of the tong are around the fitting such that the logo is positioned around the pipe and the opposite end on the neck of the fitting.

You should then use one hand to squeeze the tongs and the other to pull the pipe. It is important to disconnect the fitting cautiously and properly so the pipe is released free of any external damage or marks on its outer diameter.

SharkBite fittings are best for the use of air and are not recommended in case of usage with air or gas. It is also possible for you to experience Shark Bite fittings leaking. However, this is mainly caused by the improper fixing of the pipe. It can also be scratched on the outside of the pipe which is why it is important to check for damages before the installation of the fittings. The scratches prevent the o-ring from achieving a watertight seal and results in leakages.

SharkBite fittings are not used by professional plumbers mainly because the charges are the same even if they install any other fitting. This is why they will generally use the best materials for the job. However, if you are doing the repair or installation work at home, all by yourself, then, SharkBite is the best fitting for you because of its affordability and convenience.

SharkBite is one of the cheapest options available in terms of fittings for copper water pipes.
Disconnect Tongs and Disconnect Clips by SharkBite remove plastic insert for copper very conveniently. All you have to do is use either one to pull the plastic insert past the o-ring.
Both the connection and disconnection processes of the SharkBite fittings are very easy and convenient making it the best choice for you if you wish to fix your water pipelines at home al on your own.

CONCLUSION

The installation of SharkBite Fitting into the copper pipe itself is not a difficult task to do however, the hard part appears when you have to do all the measurement work and select the correct fitting according to the size of your pipe. However, the following charts and proper instructions can help you correctly measure and find the right sized fittings. If the fittings and pipes are not synchronized in their sizes it can be difficult to install them.

Even if they do get installed in such a manner, it is going to result in leakage or damages to your pipe which is why it is crucial to keep in mind. A secured seal and a properly connected fitting give long-term installed water pipelines which is why SharkBite is the best fittings at the friendliest prices. SharkBite fittings are also the best fitting option since it has a very simple procedure and provides the most convenient installation for domestic purposes.

Since the disconnection is also equally easy and simple, SharkBite fittings eliminate you needing any professional plumbing help and make you independent in terms of both the installation and repair of the water pipelines across your house.

Read More: How To Install Inground Pool Lights

LEAVE A REPLY

Please enter your comment!
Please enter your name here